ASTM D4258 PDF

This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D on Protective. ASTM D Standard Practice for Surface Cleaning Concrete for Coating. ASTM D (Plastic sheet test): Place plastic sheet on concrete stab for 24 hours. o ASTM-D Standard Practice for Surface Cleaning Concrete for.

Author: Gorn Kitaxe
Country: Germany
Language: English (Spanish)
Genre: Finance
Published (Last): 18 December 2013
Pages: 171
PDF File Size: 11.64 Mb
ePub File Size: 6.7 Mb
ISBN: 606-9-35134-552-9
Downloads: 58214
Price: Free* [*Free Regsitration Required]
Uploader: Fenrigis

Damaged areas must be repaired with an appropriate patching material. If the document is revised or amended, you will be notified by email.

If these requirements are ignored, the lining can delaminate from the substrate or fail to cure properly. Already Subscribed to this document.

Standard Practice for Surface Cleaning Concrete for Coating

Prime and paint as soon as possible after surface prep. Bare plaster must be cured and hard before application. Treat textured, soft, porous, or powdery plaster with a solution of 1 pint household vinegar to 1 gallon of water.

Thoroughly cleanse vinyl siding by scrubbing with a warm, soapy water solution. If necessary, pressure clean with a minimum of psi to remove all dirt, dust, oil, grease, laitance, loose particles, foreign material, and peeling r4258 defective coatings.

Proceed to Checkout Continue Shopping. Store finishing lumber and flooring in dry, warm rooms to prevent absorption of moisture, shrinkage, and roughening of the wood. Rinse thoroughly and allow to dry. Your Alert Profile lists the documents that will be monitored. The surface may be painted after 30 days if recommended procedures for applying stucco are followed, and normal drying conditions exist. As critical aastm these steps are, it should come as no surprise that there is a wealth of technical standards available from organizations such as NACEASTMand SSPC which address many aspects of steel and concrete surface preparation.

  JIM ELVIDGE THE UNIVERSE SOLVED PDF

Drywall should be clean and dry.

asym Make sure all visible grease, oil, salts, asrm soluble welding residues have been removed before hand tool cleaning by the methods outlined in SSPC-SP 1. You may delete a document from your Alert Profile at any time. All loose rust, loose mill scale, loose and other detrimental foreign matter can be removed by power tool cleaning. Ensure that the surface is clean and free of any loose stucco, and that surface pH is between 6 and 9.

zstm Procedures include broom cleaning, vacuum cleaning, air blast cleaning, water cleaning, detergent water cleaning, and steam cleaning. Allow to dry and cure thoroughly for at least 30 days prior to painting. There was so much to do before I ever opened a can of paint. Surface Preparation Proper surface preparation can improve the outcome of your coating system.

Sand surfaces smooth, taking care to sand with the grain. Check for compatibility by applying a test patch of the recommended coating system, covering at least 2 to 3 square feet. Vacuum cleaning, broom cleaning, water cleaning, air blast cleaning, and steam cleaning are suitable as outlined in ASTM D Spackle the drywall defects.

Established by the Steel Structures Council inthese methods are used throughout the world for describing methods for cleaning structural steel. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.

ASTM D – 05() Standard Practice for Surface Cleaning Concrete for Coating

Please first log in with a verified email before subscribing to alerts. Small residues of rust and paint may be left in the lower portions of pits if the original surface is pitted. Ensure that all surface contamination has been removed by washing with an appropriate cleaner. Rags and cleaning solution should be changed frequently so that deposits of oil and grease are not spread over additional areas in the cleaning process.

  BRECHT AUFSTIEG UND FALL DER STADT MAHAGONNY PDF

The surface to be coated must be clean and free of contaminants, oil, loose cement, mortar, and grease. Make sure all visible grease, oil, salts, and soluble welding residues have been removed prior to power tool cleaning by the methods outlined in SSPC-SP 1. Here is a summary of some of the published standards with which installers and specifiers of corrosion protection linings should be familiar.

Wood must be clean and dry. Galvanized metal must weather at least 6 months before coating. Surface imperfections should be corrected and cleaned prior to painting. Staining to be cleaned may consist of light shadows, slight streaks, or minor discolorations caused by stains of rust, mill scale, or previously applied paint.

Method of cleaning steel to remove dirt, oil, grease, loose rust, loose mill scale, and loose paint using water at pressures of 2, to 2, psi at a flow of 4 to 14 gallons per minute.

Clean steel using one or more of the nine surface preparations described below. The room must be ventilated while drying. Following these guidelines will help ensure sufficient adhesion of the coating and can help prolong the life of the coating system.

When viewed without magnification, a White Metal Blast Cleaned surface should be free of any visible grease, oil, dust, dirt, mill scale, paint, rust, oxides, corrosion products, and other foreign matter. Caulk should be applied after priming.

All nail heads must be set and spackled. Some composition boards may emit a waxy material that must be removed with a solvent prior to coating. We have no amendments or corrections for this standard.