BCD to. 7-Segment. Decoder. January DM74LS BCD to 7-Segment Decoder. General Description . This datasheet has been downloaded from: www. 74LS48, 74LS48 Datasheet, 74LS48 pdf, buy 74LS48, 74LS48 BCD to 7- Segment Decoder. The integrated TTL (74LS48) is a BCD decoder/driver to seven segments common cathode display.

Author: Zululrajas Kiganos
Country: Somalia
Language: English (Spanish)
Genre: Business
Published (Last): 6 May 2004
Pages: 249
PDF File Size: 6.19 Mb
ePub File Size: 3.70 Mb
ISBN: 373-6-53661-911-3
Downloads: 84654
Price: Free* [*Free Regsitration Required]
Uploader: Shaktitaur

Describe what this feature is, and why it is used.

7447 IC is wierd!

Be prepared to show your sources when answering this question in class. Learning to analyze digital circuits requires much study and practice.

Then just map the pins correctly again, from datasheet:. So, I suggest the following alternative approach: Nov 20, What is the purpose of students taking your course?

One way you can save time and reduce the possibility of error is to begin with a very simple circuit and incrementally add components to increase its complexity after each analysis, rather than building a whole new 74448 for each practice problem.

Unfortunately, that one digit begins to glow the moment the high-voltage DC supply is turned on, even before the chip receives power! It was designed to sink current when using common anode 7-segments LED. Anyone who remembers the first LCD displays on portable personal computers will recall how you could only see the display if you viewed it perpendicular to the display surface, or at a very slight angle from perpendicular.


74LS48 BCD to 7-segment Decoder Driver IC | Warefab

Yes, my password is: While this question introduces the concept of a vacuum-fluorescent VF display, it also serves as a review of shift register and latch technology. Nov 20, 8. Feb 19, 4, The behavior of the display driver IC may be represented by a truth table with seven outputs: Carefully measure those logic states, to verify the accuracy of your analysis. On the other hand, when outputting a logic LO, the output is seldom more than a few hundred millivolts above ground, which is a much more reliable drive signal not to mention the higher current capacity.

Then just map the pins correctly again, from datasheet: The timing diagram and description in the datasheet should provide plenty of information for determining how to send data to the display using this IC. Each segment on a 7-segment display is designated a letter A-G.

How Sensor Fusion Works Sensor fusion is the art of combining multiple physical sensors to produce accurate “ground truth”, even though each sensor might be Always be sure that the power supply voltage levels are within specification for the logic circuits you plan to use.

Spehro Pefhany k 4 Nov 20, 9. I have left the answer purposefully vague so that students will have to figure out how to properly use BJTs to drive the Nixie tube cathodes. When you want to light up the LED, you let the pin on to go low, this makes the pin a “ground” for the voltage source, now there is a voltage drop across the LED and there is flow of current, the LED lights up. An example of an early attempt at full-Lambertian display is the Gyricon technology developed by Xerox.


IC is wierd! | All About Circuits

In most sciences, realistic experiments are much more difficult and expensive to set up than electrical circuits. I never cease to 748 amazed at how poorly students grasp instructions when presented in a typical lecture instructor monologue format!

The answer I give here is purposefully vague, as usual. I highly recommend CMOS logic circuitry for at-home experiments, where students may not have access to a 5-volt regulated power supply. The transistor is not correct.

It merely conditions and outputs bits of information to the grids of a VF display. Read the datasheet for this device, then comment on why you think a serial rather than parallel data input format was chosen.